Gasfitter (GAS)

Date: 5/3/2022 12:57:02 PM
Module: 080106aC
Version: 21
Page:
Comment: Customer reported: Question 7 in self test says code is 6.2.9. It is now 6.2.10. in the 2020 b149.1 Current info in V21 appears to be behind the new Gas Codebook. May also impact 060104bB Introduction to Gasfitting Codes and Regulations.
Status: Approved for Review

Date: 6/26/2023 1:33:01 PM
Module: 080106aC_2006
Version: 24
Page: 43
Comment: Tubing laid on rooftop shall be supported continuously is clause 6.25.2 , not 6.26.2 in my version of B-149.1-15 Thanks!
Status: Approved for Review

Date: 9/6/2024 1:05:01 PM
Module: 210101a
Version: 24
Page: 31
Comment: Question 1 asks for requirements on a site with five to nine workers. Based on the answer key, the question should ask for requirements on a site with 50-99 workers.
Status: Approved for Review

Date: 11/2/2023 10:51:29 AM
Module: 210101c
Version: 24
Page: 16, 17
Comment: Shows image of MSDS Not SDS this was a change from 2015
Status: Approved for Review

Date: 11/2/2023 10:24:52 AM
Module: 210101c
Version: 24
Page: 3
Comment: The Figure 1 references msds should be SDS
Status: Approved for Review

Date: 11/26/2023 1:13:07 PM
Module: 210103bA
Version: 24
Page: 21 -41
Comment: The Test and the Answers Do not match they are not in the right order and the key goes to 11 and the test goes to 9
Status: Approved for Review

Date: 1/15/2024 1:27:16 PM
Module: 210103bA
Version: 24
Page: 21 and 41
Comment: Questions and answers don't line up
Status: Approved for Review

Date: 11/3/2021 12:26:49 PM
Module: 210104b
Version: 21
Page: 37
Comment: Self test gives answers to 17 questions but there are only 9 questions in the self test and one of them is missing a question number
Status: Implemented

Date: 10/10/2024 1:24:49 PM
Module: 210104b
Version: 24
Page: 3-4
Comment: Paragraph one of page 3 states, "Figure 3 shows the elbow opening away from the viewer". It should read "Figure 2 shows the elbow opening away from the viewer". Paragraph two of page 3 states, "Figure 4 shows a threaded elbow opening toward the viewer". It should say, "Figure 3...". Paragraph three of page 3 states, "Figure 5, uses the same lines and rules as with the 90° elbow in Figure 1, making it easy to identify." It should say, "Figure 4, uses the same lines and rules as with the 90° elbow...". Paragraph one on page 4 states, "In Figure 6 we see in the actual pipe drawing, the main pipe is obscured by the opening of the tee facing the viewer, and a threaded connection on the other side". It should say, "In Figure % we see...".
Status: Approved for Review

Date: 10/18/2024 8:36:07 AM
Module: 210104b
Version: 24
Page: 5
Comment: Figure 8 "Butt Weld Fitting Symbols" show Reducer Concentric and Reducer Eccentric without the welded connection dot symbol. The welded connection dot is displayed in the Objective One Activity on Figure 12 (page 8). Recommend updating Figure 8 to include the weld symbol.
Status: Approved for Review

Date: 10/18/2024 12:15:30 PM
Module: 210104c
Version: 24
Page: 66
Comment: It appears that self-test questions 11-13 have been deleted, without removing answers from the key on page 66. Delete 11, 12, and 13, then change answer #14 to #11.
Status: Approved for Review

Date: 1/3/2025 3:01:58 PM
Module: 210105b
Version: 24
Page: 38-39
Comment: The Objective One Activity Answers' key numbers are out of sequence, as of question #6.
Status: Approved for Review

Date: 1/3/2025 2:32:00 PM
Module: 210105b
Version: 24
Page: 15
Comment: Near the top of the page it says, “Area = πd x h or πdh and the area of each end is π²”. Update the end of the sentence to say, “the area of each end is πr²”.
Status: Approved for Review

Date: 1/3/2025 2:23:28 PM
Module: 210105b
Version: 24
Page: 6
Comment: Objective One Activity, question 1 asks “In the equation, 9-6+15x7÷4=, what is the first portion to be solved”. The answer provided is “7÷4”, which is incorrect. The correct answer is “15x7”, as multiplication and division are given equal priority in the order of operations.
Status: Approved for Review

Date: 1/3/2025 2:17:08 PM
Module: 210105b
Version: 24
Page: 4-5
Comment: The Order of Operations text states, “The order of operations is remembered with the acronym BEDMAS taking the first initial of each word”. Further text needs to be included to state “DIVISION and MULTIPLICATION are given equal priority when solving from left to right, then ADDITION and SUBTRACTION are given equal priority when solving from left to right”. The equation provided on pages 4 and 5 is solved inaccurately. The break down is correct up to this point: 9+5x8÷2-3+48÷24. From there the text says, “DIVISION must be completed before MULTIPLICATION”. In fact, they are considered equal, and all multiplication and division should be solved in the same sequence. As are addition and subtraction in the next step of BEDMAS. The equation above should solve as follows: 9+5x8÷2-3+48÷24 9+20-3+2 =28 Please update wording, correct order of operations, and double check other equations in the module.
Status: Approved for Review

Date: 12/5/2023 3:10:07 PM
Module: 210105g
Version: 24
Page: 22
Comment: Selftest: Question 11 - answer d) should read: "Load" (not "Toad" :)
Status: Approved for Review

Date: 12/5/2023 3:07:34 PM
Module: 210105g
Version: 24
Page: 25
Comment: Objective Two Exercise Answers (pg25)- Answer to question 3 (exercise on pg. 16) should be: d) Series-parallel
Status: Approved for Review